Honeywell Genesis 7580G User Manual Download

Page: 84 / 202

6 - 4

Code 39

< Default All Code 39 Settings >

Code 39 On/Off

Code 39 Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/

Stop characters.

Default =

Don’t Transmit.

Code 39 Check Character

No Check Character

indicates that the scanner reads and transmits bar code data with or without a check character.

When Check Character is set to

Validate, but Don’t Transmit

, the unit only reads Code 39 bar codes printed with a check

character, but will not transmit the check character with the scanned data.

When Check Character is set to

Validate and Transmit

, the scanner only reads Code 39 bar codes printed with a check

character, and will transmit this character at the end of the scanned data.

Default = No Check Character.

* On

Off

Transmit

* Don’t Transmit

* No Check Character

Validate, but Don’t Transmit

Validate and Transmit

Summary of Contents for Genesis 7580G











































































































































































































Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands

Honeywell Genesis 7580G, User Manual

Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands