Honeywell Genesis 7580G User Manual Download

Page: 44 / 202

3 - 2

Good Read and Error Indicators

Beeper – Good Read

The beeper may be programmed

Off

in response to a good read. Turning this option off only turns off the beeper

response to a good read indication. All error and menu beeps are still audible.

Default = Beeper - Good Read On.

Beeper Volume – Good Read

The beeper volume codes modify the volume of the beep the scanner emits on a good read.

Default = High.

Beeper Pitch – Good Read

The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.

Default = Medium.

Beeper - Good Read Off

* Beeper - Good Read On

Low

Medium

* High

Off

Low (1600 Hz)

* Medium (2700 Hz)

Summary of Contents for Genesis 7580G











































































































































































































Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands

Honeywell Genesis 7580G, User Manual

Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands