Honeywell Genesis 7580G User Manual Download | Manualshive

Page: 81 / 202

background image

6 - 1

6

Symbologies

This programming section contains the following menu selections. Refer to

for settings and defaults.

All Symbologies

If you want to decode all the symbologies allowable for your scanner, scan the

All Symbologies On

code. If on the other hand,

you want to decode only a particular symbology, scan

All Symbologies Off

followed by the On symbol for that particular sym-

bology.

Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.

Message Length Description

You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code
doesn’t match the valid reading length, the scanner will issue an error tone. You may wish to set the same value for minimum
and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.

EXAMPLE:

Decode only those bar codes with a count of 9-20 characters.
Min. length = 09Max. length = 20

•

All Symbologies

•

Interleaved 2 of 5

•

•

•

China Post (Hong Kong 2 of 5)

•

•

Chinese Sensible (Han Xin) Code

•

•

•

•

•

•

•

•

•

Postal Codes - 2D

•

•

Postal Codes - Linear

•

Code 32 Pharmaceutical (PARAF)

•

•

•

GS1 DataBar Omnidirectional

•

•

•

•

Straight 2 of 5 IATA (two-bar start/stop)

•

•

Straight 2 of 5 Industrial (three-bar start/stop)

•

•

TCIF Linked Code 39 (TLC39)

•

GS1 Composite Codes

•

•

GS1 DataBar Expanded

•

•

GS1 DataBar Limited

•

•

GS1 DataBar Omnidirectional

•

UPC-A/EAN-13 with Extended Coupon Code

•

•

•

•

All Symbologies On

All Symbologies Off

«
...
79
80
81
82
83
...
»

Summary of Contents for Genesis 7580G











































































































































































































Reviews:

No comments

Related manuals for Genesis 7580G

Brand: JARLTECH Pages: 59

Brand: TrekStor Pages: 86

Webster's Spelling Corrector NC-10

Brand: Franklin Pages: 8

FuzzyScan FA460

Brand: Cino Pages: 67

Brand: Aluratek Pages: 2

Brand: Symbol Pages: 352

Brand: Stealth Cam Pages: 24

Brand: AuthenTrend Pages: 17

Brand: GPRINTER Pages: 85

Brand: Elkron Pages: 2

Brand: mt-mobility Pages: 3

Brand: Flash Pages: 190

Brand: Unitech Pages: 2

Brand: Square Pages: 5

Brand: RIOTEC Pages: 3

Brand: RIOTEC Pages: 3

Brand: RIOTEC Pages: 3

Brand: Videx Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands