Honeywell Genesis 7580G User Manual Download

Page: 42 / 202

2 - 22

Scanner-Bioptic ACK/NAK Mode

Bioptic ACK/Nak On

must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet

is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.

Default =

Bioptic ACK/NAK Off.

Scanner-Bioptic ACK/NAK Timeout

This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the bar
code below, then set the timeout (from 1-30,000 milliseconds) by scanning digits from the inside back cover, then scanning

Save

Default = 5100.

* Bioptic ACK/NAK Off

Bioptic ACK/NAK On

ACK/NAK Timeout

Summary of Contents for Genesis 7580G











































































































































































































Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands

Honeywell Genesis 7580G, User Manual

Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands