Honeywell Genesis 7580G User Manual Download | Manualshive

Page: 117 / 202

background image

6 - 37

UPC/EAN Version

Scan the

UPC/EAN Version On

bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear compo-

nent. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.)

Default = UPC/EAN Ver-

sion Off.

Note: If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from

the GS1 DataBar code. See

Coupon GS1 DataBar Output

(page 6-21) for further information.

GS1 Composite Code Message Length

Scan the bar codes below to change the message length. Refer to

Message Length Description

(page 6-1) for additional

information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.

GS1 Emulation

The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent
GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and
GS1-128 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recog-
nize one data carrier type.)

If

GS1-128 Emulation

is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID

is enabled, the value will be the GS1-128 AIM ID, ]C1 (see

Symbology Charts

If

GS1 DataBar Emulation

is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM

ID is enabled, the value will be the GS1-DataBar AIM ID, ]e

m

Symbology Charts

If

GS1 Code Expansion Off

is scanned, retail code expansion is disabled, and UPC-E expansion is controlled by the

(page 6-22) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see

Symbology Charts

If

EAN8 to EAN13 Conversion

is scanned, all EAN8 bar codes are converted to EAN13 format.

Default = GS1 Emulation Off

.

UPC/EAN Version On

* UPC/EAN Version Off

Minimum Message Length

Maximum Message Length

GS1-128 Emulation

«
...
115
116
117
118
119
...
»

Summary of Contents for Genesis 7580G











































































































































































































Reviews:

No comments

Related manuals for Genesis 7580G

Brand: Ortus Pages: 11

SmartTerminal ST-1044

Brand: Cherry Pages: 4

Brand: Renkforce Pages: 4

Infinea Tab 2 LPT

Brand: Infinite Peripherals Pages: 26

Brand: Atid Pages: 15

Brand: Atid Pages: 46

Brand: IFM Electronic Pages: 37

SCRIBA 150 White 2 GB

Brand: WOXTER Pages: 1

Brand: Sony Pages: 2

Brand: Sony Pages: 3

Brand: Sony Pages: 242

Brand: Sony Pages: 263

Brand: COMPANION Pages: 6

Barcode Reader P4 BCR

Brand: Banner Pages: 2

Brand: MAG Pages: 2

Brand: Viking Pages: 20

Brand: Datalogic Pages: 129

Brand: Manta Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands