Honeywell 145*g1D User Manual Download Page 36

Page: 36 / 206

2 - 18

Turbo Mode:

The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.

Default = Off.

Numeric Keypad Mode:

Sends numeric characters as if entered from a numeric keypad.

Default = Off.

Automatic Direct Connect Mode:

This selection can be used if you have an IBM AT style terminal and the system is dropping

characters.

Default = Off.

RS232 Modifiers

RS232 Baud Rate

Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the

same baud rate as the scanner.

Default = 9600.

Turbo Mode On

* Turbo Mode Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

Automatic Direct Connect Mode

* Automatic Direct Connect

Mode Off

300

600

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands