Honeywell 145*g1D User Manual Download Page 186

Page: 186 / 206

12 - 2

Replacing a Corded Scanner Interface Cable

1. Turn the power to the host system OFF.

2. Disconnect the scanner’s cable from the terminal or computer.

3. Locate the small hole on the back of the scanner’s handle. This is the cable release.

4. Straighten one end of a paper clip.

5. Insert the end of the paper clip into the small hole and press in. This depresses the retention

tab, releasing the connector. Pull the connector out while maintaining pressure on the paper
clip, then remove the paper clip.

6. Replace with the new cable.

Insert the connector into the opening and press firmly. The connector is keyed to go in only
one way, and will click into place.

Replacing Cables and Batteries in Cordless Systems

Replacing an Interface Cable in a Base

1. Turn the power to the host system OFF.

2. Disconnect the base’s cable from the terminal or computer.

3. Turn the base upside down.

4. Pull the connector out while maintaining pressure on the connector release clip.

5. Replace with the new cable.

Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into
place.

Cable
Release

CCB01-010BT Base :

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands