Honeywell 145*g1D User Manual Download Page 123

Page: 123 / 206

7 - 21

UPC-E0 Addenda Required

When

Required

is scanned, the scanner will only read UPC-E bar codes that have addenda.

Default = Not Required.

UPC-E0 Addenda Separator

When this feature is

, there is a space between the data from the bar code and the data from the addenda. When turned

Off

, there is no space.

Default = On.

UPC-E0 Check Digit

Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.

Default = On.

UPC-E0 Leading Zero

This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan

Off

Default = On.

Required

* Not Required

* On

Off

* On

Off

* On

Off

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands