Honeywell 145*g1D User Manual Download Page 69

Page: 69 / 206

3 - 27

Host ACK On/Off

Host ACK Responses

Command

Action

[ESC] a,

Double beeps to indicate a successful menu change was made.

[ESC] b,

Razz or error tone to indicate a menu change was unsuccessful.

[ESC] 1,

The green LED illuminates for 135 milliseconds followed by a pause.

[ESC] 2,

The green LED illuminates for 2 seconds followed by a pause.

[ESC] 3,

The green LED illuminates for 5 seconds followed by a pause.

[ESC] 4,

Emits a beep at a low pitch.

[ESC] 5,

Emits a beep at a medium pitch.

[ESC] 6,

Emits a beep at a high pitch.

[ESC] 7,

Beeps to indicate a successful decode and communication to host.

[ESC] 8,[ESC] 8,

Razz or error tone to indicate a decode/communication to host was unsuccessful.

Host ACK On

* Host ACK Off

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands