Honeywell 145*g1D User Manual Download Page 122

Page: 122 / 206

7 - 20

Coupon GS1 DataBar Output

If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1
DataBar code. Scan the

GS1 Output On

code below to scan and output only the GS1 DataBar code data.

Default = GS1 Out-

put Off.

UPC-E0

<Default All UPC-E Settings>

UPC-E0 On/Off

Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the

UPC-E0 On

selection. If you need to

read codes that lead with the 1 number system, use

UPC-E1

(page 7-22).

Default = On.

UPC-E0 Expand

UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format.

Default = Off.

* GS1 Output Off

GS1 Output On

* UPC-E0 On

UPC-E0 Off

* Off

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands