Honeywell 145*g1D User Manual Download Page 12

Page: 12 / 206

1 - 2

Note: The power supply must be ordered separately, if needed.

2. If you are connecting a CCB01-010BT Base, make sure the cables are secured in the wireways in the bottom of the

cordless base and the base sits flat on a horizontal surface.

3. The scanner beeps.

4. Verify the scanner or cordless base operation by scanning a bar code from the

Sample Symbols

in the back of this

manual.

The unit defaults to a USB PC Keyboard. Refer to

page 2-3

for other USB terminal settings.

For additional USB programming and technical information, refer to “USB Application Note,” available at

www.honey-

wellaidc.com.

Connecting with Keyboard Wedge

A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner
provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection:

1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer.

2. Connect the appropriate interface cable to the device and to the terminal/computer.

CCB01-010BT Base
USB Connection:

Corded Voyager 1450g
Keyboard Wedge Connection:

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands