Hobbies & Helis Quick 60 Assembly & Parts Listing Download | Manualshive

Page: 40 / 54

background image

Install (1) 5 x 10 x 4 Flanged
Bearing into the Right Tail case
Side Plate

Install (1) Tail pulley gear to the (1)
Tail Output Shaft using (1) M3-3
Set Screw

Install a (2) Tail Pulley Gear
Spacers on each side of the Tail
Pulley Gear

Install the Tail Pulley Gear
Assembly into the 5x 10 x 4
Bearing in the right Tail Case Side
Plate.

Install (1) Tail belt through the
boom and around the Tail Pulley
Gear.

«
...
38
39
40
41
42
...
»

Summary of Contents for Quick 60























































Reviews:

No comments

Related manuals for Quick 60

Brand: Harbor Freight Tools Pages: 7

Brand: Quadro Pages: 11

Baby Annabell 794982

Brand: Zapf Creation Pages: 2

Brand: Zapf Creation Pages: 24

Brand: REVELL Pages: 12

Sand & Water Fun Farm 7165

Brand: Step2 Pages: 4

Brand: Accucraft trains Pages: 6

Brand: Cobra Helicopter Pages: 40

Animated Caboose 73-6729-250

Brand: Lionel Pages: 4

Brand: Mega Construx Pages: 32

Brand: marklin Pages: 32

Brand: Top R/C Hobby Pages: 13

Brand: Faller Pages: 8

Brand: Fisher-Price Pages: 6

Brand: Tadano Pages: 16

Fur Real Friends Baby Cuddles My Giggly Monkey Happy to See Me Pets

Brand: Hasbro Pages: 2

SBach 342 Thunderbolt

Brand: SkyLine Pages: 26

SPEED MASTER TG511

Brand: THINK GIZMOS Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands