background image

1610 Interstate Drive  Champaign, IL 61822

(217) 398-8970, Ext. 2

[email protected]

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Hobbico

®

guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or modification. In no case shall Hobbico’s liability exceed the original cost
of the purchased kit. Further, Hobbico reserves the right to change or modify this warranty without notice.

In that Hobbico has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return
this kit immediately in new and unused condition to the place of purchase.

HCAZ3084 for HCAA2020  V:1.0 

© Copyright 2002

See more of our products at 

www.hobbico.com

Wingspan: 60 in [1524mm]
Wing Area: 660 sq in [42.6dm

2

]

Weight: 5.5 lbs [2495g]
Wing Loading: 19 oz/ sq ft [58 g/dm

2

]

Engine: .40 cu in [6.5cc] two-stroke
Radio: 4-channel, 4 servos

Summary of Contents for Superstar 40 ARF

























Reviews: