TRANSPORTING
6-49
EXTENDING THE SIDE FRAME
Required Tools
• Slinging Rope (20 mm dia.×8 m, 6×37 Ordinary Z lay Class
A, Applicable Max. Load: 3 tons) .....................................6 Used
* Before slinging, make sure no broken wire strands
and/or kinks exist.
• Lever Block (JIS B8819 equivalent to L3.2T) ................2 Used
* Check that there is no damage on the lever block.
• Power Boost Wrench (including accessories), width across
flats of the torque wrench: 50 mm, 55 mm
• Air Compressor (slide surface cleaning)
• Soft Protectors
d
WARNING:
• Group work is required. Before starting work,
coordinate work procedures with co-workers.
• Damage to the lever block and/or wire rope
may result along with severe personal injury.
When extending side fame (3) using the front
attachment, do not allow any personnel to enter
the vicinity of the machine.
d
WARNING: Do not loosen side frame guide bolts (9).
IMPORTANT: When the machine is shipped from the
factory, all side frame tightening bolts are
not installed. Therefore, unbolted screw
holes on side frame (3) are coated with rust-
inhibitor so that they may be clogged with
dust or soil. Before installing the tightening
bolts, clean the thread surface thoroughly.
If the bolts are difficult to tighten, tap the
screw holes again.
Tap: M33, Pitch: 3 mm (ZX450LC
-3
)
Tap: M36, Pitch: 3 mm (ZX650LC
-3
, 850LC
-3
)
IMPORTANT: Before working, completely clean side
frame (3) slide surfaces using compressed
air. If mud and/or gravel is stuck on the
contact areas of track frame (2) and side
frame (3), the work may be interrupted and
loose mounting bolts (1) may result.
1. Remove side frame mounting bolts (1) (6 used, 3 bolts
in two places : ZX450LC
-3,
8 used, 4 bolts in two places :
ZX650LC
-3
, 850LC
-3
) from extending side frame (3).
2. Rotate the upper structure to the side of the extending
side frame until the front attachment faces side frame (3)
perpendicularly.
3. Set the arm and boom angle between 90° to 110°. Then,
lower the bucket bottom to the ground.
M111-06-011
M166-01-233
1
3
2
1
9
90 to 110°
M162-06-001
1
3
2
1
9
ZX450LC
-3
ZX650LC
-3
, 850LC
-3
Summary of Contents for ZAXIS 450LC-3
