Hitachi Ultrastar 15K73 Reference Manual Download Page 142

Page: 142 / 273

OEM MANUAL:K6602924

5 COMMAND DESCRIPTIONS

Revision: 1 / Date: 2003.03.06

Page: 142 / 273

If this number of blocks is greater than the Maximum Pre-fetch Ceiling, then the

number of logical blocks maximally pre-fetched shall be truncated to the value

stored in the Maximum Pre-fetch Ceiling field.

A FSW(Force Sequential Write) bit of one indicates that the controller writes the

multiple block writes to the media in an ascending, sequential, logical block order.

A FSW bit of zero indicates that the controller reorders the sequence of writing

addressed logical blocks in order to achieve a faster command completion.

Since the controller does not support FSW bit, this bit is ignored.

The Disable Read-Ahead(DRA) bit, when one, requests that the device server not

read into the buffer any logical blocks beyond the addressed logical block(s).

When the DRA bit equals zero, the device server may continue to read logical

blocks into the buffer beyond the addressed logical block(s).

The Logical Block Cache Segment Size(LBCSS) bit when one, indicates that the

Cache Segment Size field units shall be interpreted as logical blocks. When the

LBCSS bit equals zero the Cache Segment Size field units shall be interpreted as

butes. The LBCSS shall not impact the units of other field.

The Number of Cache segment specifies how many segments the host requests

that the cache be divided into.

The Cache Segment Size field indicates the requested segment size in bytes. This

standard defines that the Cache Segment Size field is valid only when SIZE bit is

one.

[ Mode Page A

]

Table 5.48 Control Mode Page (Page Code = A

)

Bit

Byte

Reserved

SPF

Page Code(0A

)

Page Length(0A

)

Reserved

GLTSD RLEC

(cont

’

MODE SELECT:(15h)

Summary of Contents for Ultrastar 15K73


















































































































































































































































































Search results

Summary of Contents for Ultrastar 15K73

Reviews:

Brands by name

Popular brands

Hitachi Ultrastar 15K73, Reference Manual

Search results

Summary of Contents for Ultrastar 15K73

Reviews:

Brands by name

Popular brands