Hitachi KP-D5000, Operation Manual

Page: 14 / 54

21
AGC setting
AGC mode setting
1) Press the Set button for longer than 2 seconds to display the
Main menu.
2) Use the Up and Down buttons to move the cursor to AGC.
AGC setting data blinks.
3) In this state, push the Set button to display AGC MENU.
4) When the cursor is at
MODE , push the Set button to change
the AGC modes as follows.
Set button :
ON → OFF
ON : Automatically changes the video level within
a range of the AGC limit as appropriate according to
the brightness of subject. AGC is set to ON in
factory setting.
OFF : Always sets a fixed video level from the [FIX. GAIN].
◆
◆ ◆
◆
ＡＧＣ
ＡＧＣ ＡＧＣ
ＡＧＣ ＭＥＮＵ
ＭＥＮＵ ＭＥＮＵ
ＭＥＮＵ
◆
◆ ◆
◆
> > > >
ＭＯＤＥ ＭＯＤＥ ＭＯＤＥ ＭＯＤＥ ：ＯＮ ：ＯＮ ：ＯＮ ：ＯＮ
ＡＧＣ
ＡＧＣ ＡＧＣ ＡＧＣ ＬＩＭＩＴ ＬＩＭＩＴ ＬＩＭＩＴ ＬＩＭＩＴ ：＋ ：＋ ：＋ ：＋３１ ３１ ３１ ３１
０ ０ ０ ０・・・・・・・・ ・・・・・・・・ ・・・・・・・・ ・・・・・・・・● ● ● ●・・・・・・ ・・・・・・ ・・・・・・ ・・・・・・５１ ５１ ５１ ５１
DNR
DNR DNR
DNR ：
： ：
：OFF
OFF OFF
OFF
ＲＥＴ
ＲＥＴ ＲＥＴ
ＲＥＴ
ＥＮＤ
ＥＮＤ ＥＮＤ
ＥＮＤ
……
AGC mode display
……
AGC lmit (0~+51)
……
AGC limit gauge
……
Digital Noise Reduction （ DNR ） display
…… Return to Main menu
……
End (Menu display off
）
AGC setting menu ( ON)
メイン設定メニュー
<<<
ＭＡＩＮ ＭＥＮＵ
>>>
ＴＩＴＬＥ ：ＯＦＦ
↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ ↵
>
ＡＧＣ ：ＯＮ（３１ｄＢ）
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＡＵＴＯ（ＭＩＤ）
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ ↵
ＤＩＧＩＴＡＬ ＺＯＯＭ ：ＯＦＦ ↵
ＳＵＢ ＭＥＮＵ ↵
ＥＮＤ
AGC limit setting (AGC ON)
1) When the cursor is at AGC LIMIT , push the Set button.
A mark[●] at the AGC limit gauge flashes.
2) In this state, use the Up and Down buttons to change
the AGC limit.( 0
～
+51). For factory setting by the Scene file
(page 17), hold down both the Up and Down buttons
simultaneously for 2 seconds.
3) In this state, pressing Set button will stop blinking and setting
value will be fixed. The the cursor moves to RET .
AGC limit setting (AGC OFF)
1) When the cursor is at
FIX GAIN , push the Set button.
A mark[●] at the FIX GAIN gauge flashes.
◆
◆ ◆
◆
ＡＧＣ ＡＧＣ ＡＧＣ ＡＧＣ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
◆
◆ ◆
◆
> > > >
ＭＯＤＥ
ＭＯＤＥ ＭＯＤＥ
ＭＯＤＥ ：Ｏ
：Ｏ ：Ｏ
：ＯFF
FF FF
FF
ＦＩＸ
ＦＩＸ ＦＩＸ ＦＩＸ ＧＡＩＮ ＧＡＩＮ ＧＡＩＮ ＧＡＩＮ ：＋ ：＋ ：＋ ：＋３１ ３１ ３１ ３１
－ － － －６ ６ ６ ６・・・・・・・・ ・・・・・・・・ ・・・・・・・・ ・・・・・・・・● ● ● ●・・・・・・ ・・・・・・ ・・・・・・ ・・・・・・５１ ５１ ５１ ５１
DNR
DNR DNR DNR ： ： ： ：OFF OFF OFF OFF
ＲＥＴ ＲＥＴ ＲＥＴ ＲＥＴ
Ｅ
Ｅ Ｅ
ＥＮＤ
ＮＤ ＮＤ
ＮＤ
……
AGC mode display
……
AGC lmit ( － 6~+51)
……
AGC limit gauge
……
Digital Noise Reduction （ DNR ） display
…… Return to Main menu
…… End (Menu display off ）
AGC setting menu ( OFF)
22
AIE mode
AIE is a function to correct brightness of the part that has
darkened as a result of over exposure control by BLC and
PEAK/AVE.
When the cursor is at
AIE , push the Set button to change the
AIE modes as follows.
Set button :
OFF→LOW→MID→HIGH
OFF : AIE is inactive.
It is set for AIE in factory setting.
LOW, MID, HIGH : AIE is effective.
The enhancement level of the part that
has darkened is changed to
LOW, MID, HIGH.
5) Move the cursor to PK/AV and push Set button to
display the ratio of peak and average.
Set button :
0/100→ 15/ 85→ 30/ 70→ 50/ 50
→ 75/ 25→ 100/0
The response to spot light increases with increment
in peak value. Factory setting is 15/85.
Note
The part that has darkened is corrected brightness by
the enhancement level increment, but the picture might
be noisy. Therefore, set the enhance level with taking
picture conditions.