Hitachi KP-D5000, Operation Manual

Page: 13 / 54

.
19
Back light control mode setting
The lens iris closes in response to brightness when strong
light or sun light is hitting the spot besides the place to be
observed, and the subject of interest becomes dark. This
mode is used to avoid darkening of subject of interest in such
condition.
1) Press the Set button for longer than 2 seconds to display
the Main menu.
2) Use the Up and Down buttons to move the cursor to
LIGHT CONTROL . [AVE]/[BLC]/[PK/AVE] flashes.
3) In this state, push the Set button to display LIGHT
CONTROL MENU .
4) When the cursor is at MODE , push the Set button and
select BLC. The following menu is displayed.
◆ ◆ ◆ ◆
ＬＩＧＨＴ ＬＩＧＨＴ ＬＩＧＨＴ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
◆ ◆ ◆ ◆
> > > >
ＭＯＤＥ
ＭＯＤＥ ＭＯＤＥ
ＭＯＤＥ ：ＢＬＣ
：ＢＬＣ ：ＢＬＣ
：ＢＬＣ
ＡＲＥＡ
ＡＲＥＡ ＡＲＥＡ ＡＲＥＡ ＳＥＬＥＣＴ：ＮＯ． ＳＥＬＥＣＴ：ＮＯ． ＳＥＬＥＣＴ：ＮＯ． ＳＥＬＥＣＴ：ＮＯ．１ １ １ １ ↵ ↵ ↵ ↵
ＬＥＶＥＬ
ＬＥＶＥＬ ＬＥＶＥＬ ＬＥＶＥＬ ： ： ： ： ００ ００ ００ ０００ ０ ０ ０
ＡＩＥ ＡＩＥ ＡＩＥ ＡＩＥ : : : : Ｏ Ｏ Ｏ ＯFF FF FF FF
↑
↑ ↑
↑
ＲＥＴ ＲＥＴ ＲＥＴ ＲＥＴ
ＥＮＤ
ＥＮＤ ＥＮＤ
ＥＮＤ
……
Light control mode display
……
Photomatric
Area select : No.1
～
9
……
Video level adjustment(-128 ～ 000 ～ +127)
…… AIE mode
…… Return to Main menu
…… End(Menu display off ）
Light control menu [ BLC ]
5) Move the cursor to AREA SELECT and push Set button to
display the detection area select menu.
6) There are
9 light detection areas that can be selected by the
Up and Down buttons. Select the areas from No. 1 to 9 such
that subject of interest enters in the selected area.
It is set to No.1 in factory setting.
Up button : 1→2→3→4→5→6→7→8→9
(ascending order)
Down button: 9→8→7→6→5→4→3→2→1
(descending order)
7) After deciding the detection area, press the Set button to
return to the LIGHT CONTROL MENU .
ＡＲＥＡ（ＢＬＣ） ＡＲＥＡ（ＢＬＣ） ＡＲＥＡ（ＢＬＣ） ＡＲＥＡ（ＢＬＣ）
ＮＯ． ＮＯ． ＮＯ． ＮＯ．１ １ １ １
┏━━━━━━┓ ┏━━━━━━┓ ┏━━━━━━┓ ┏━━━━━━┓
┃ ┃ ┃ ┃ ┃ ┃ ┃ ┃
┃ ┃ ┃ ┃ ┃ ┃ ┃ ┃
┗━━━━━━┛ ┗━━━━━━┛ ┗━━━━━━┛ ┗━━━━━━┛
Detection area setting menu
Area position and number
6
6 6
6 5
5 5
5 4 4 4 4
2
2 2
2
1 1 1 1 3 3 3 3
7
7 7
7
8 8 8 8 9 9 9 9
Peak/Average mode setting
When there is strong light spot within the image, the near by
area of spot may have overexposure and the subject might not
be confirmed. This mode is used when taking picture under
such condition. It can control overexposure in such conditions.
1) Press the Set button for longer than 2 seconds to
display the Main menu.
2) Use the Up and Down buttons to move the cursor to
LIGHT CONTROL . [AVE]/[BLC]/[PK/AVE] flashes.
3) In this state, push the Set button to display LIGHT
CONTROL MENU.
4) When the cursor is at MODE , push the Set button
and select PEAK/AVE . The following menu is displayed.
Note
1) The backlighting compensation of a central emphasis is
set at the time of electronic zoom operation.
2) The back light control mode does not operate in case of
using video signal input type auto iris lens.
Note
In case of using video signal input type auto iris lens
1) Lens iris operates by the sensitivity setting of lens
regardless light control mode setting.
2) When the LENS TYPE setting of the camera is
set to VIDEO , the lens sensitivity setting adjustment
gauge (Lev/Ref) is displayed on LIGHT CONTROL
MENU .
。
3) Set the sensitivity on the lens such that the Video
output level setting [Lev] should not fall less than the
standard level of the exposure control [Ref] .
4) If it is adjusted lower than the value of [Ref] , the
repetition phenomenon of the lens iris control and the
AGC control (Hunting) might be generated.
◆ ◆ ◆ ◆
ＬＩＧＨＴ ＬＩＧＨＴ ＬＩＧＨＴ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
◆ ◆ ◆ ◆
> > > >
ＭＯＤＥ
ＭＯＤＥ ＭＯＤＥ
ＭＯＤＥ ：ＡＶＥＲＡＧＥ
：ＡＶＥＲＡＧＥ ：ＡＶＥＲＡＧＥ
：ＡＶＥＲＡＧＥ
Ｌｅｖ
Ｌｅｖ Ｌｅｖ Ｌｅｖ |||||||||||||||||||||||||||||||||||||||||||||||･･･････････････････････ ･･･････････････････････ ･･･････････････････････ ･･･････････････････････
Ｒｅｆ Ｒｅｆ Ｒｅｆ Ｒｅｆ ||||||||||||||||||||||||||||||||||||||||||||||･･･････････････････････ ･･･････････････････････ ･･･････････････････････ ･･･････････････････････
ＬＥＶＥＬ ＬＥＶＥＬ ＬＥＶＥＬ ＬＥＶＥＬ ： ： ： ： ０００ ０００ ０００ ０００
ＡＩＥ ＡＩＥ ＡＩＥ ＡＩＥ ：ＯＦ ：ＯＦ ：ＯＦ ：ＯＦＦ Ｆ Ｆ Ｆ
ＲＥＴ ＲＥＴ ＲＥＴ ＲＥＴ
ＥＮＤ
ＥＮＤ ＥＮＤ
ＥＮＤ
……
Light control mode display
……
Video output level gauge
…… Light control standard level gauge
…… Video level adjustment(-128 ～ 000 ～ +127 ）
…… AIE mode
…… Return to Main menu
…… End (Menu display off ）
Light control menu [ AVERAGE ]
◆
◆ ◆
◆
ＬＩＧＨＴ
ＬＩＧＨＴ ＬＩＧＨＴ
ＬＩＧＨＴ ＣＯＮＴＲＯＬ
ＣＯＮＴＲＯＬ ＣＯＮＴＲＯＬ
ＣＯＮＴＲＯＬ ＭＥＮＵ
ＭＥＮＵ ＭＥＮＵ
ＭＥＮＵ
◆
◆ ◆
◆
ＭＯＤＥ ＭＯＤＥ ＭＯＤＥ ＭＯＤＥ ：ＰＥＡＫ／ＡＶＥ ：ＰＥＡＫ／ＡＶＥ ：ＰＥＡＫ／ＡＶＥ ：ＰＥＡＫ／ＡＶＥ
>
> >
>
ＰＫ／ＡＶ ＰＫ／ＡＶ ＰＫ／ＡＶ ＰＫ／ＡＶ ： ： ： ： １５ １５ １５ １５／ ／ ／ ／ ８５ ８５ ８５ ８５
ＬＥＶＥＬ
ＬＥＶＥＬ ＬＥＶＥＬ ＬＥＶＥＬ ： ： ： ： ０００ ０００ ０００ ０００
ＡＩＥ
ＡＩＥ ＡＩＥ
ＡＩＥ :
: :
: Ｏ
Ｏ Ｏ
ＯFF
FF FF
FF
↑
↑ ↑
↑
ＲＥＴ
ＲＥＴ ＲＥＴ
ＲＥＴ
ＥＮＤ ＥＮＤ ＥＮＤ ＥＮＤ
……
Light control mode display
……
Peak level ／ Average
……
Video level adjustment(-128 ～ 000 ～ +127)
…… AIE mode
…… Return to Main menu
……
End (Menu display off
）
Light control menu [ PEAK/AVE ]
20