manualshive.com logo in svg

Hitachi H8/3935, Hardware Manual

Share
Download
Hitachi H8/3935 Hardware Manual Download Page 145

133

Section 8   I/O Ports

8.1

Overview

The H8/3937 Series and H8/3937R Series are provided with six 8-bit I/O ports, two 4-bit I/O
ports, one 3-bit I/O port, and one 8-bit input-only port. Also provided are one internal 5-bit I/O
port and one internal 1-bit input-only port capable of interfacing to the on-chip FLEX™ decoder.
Table 8-1 indicates the functions of each port.

Each port has of a port control register (PCR) that controls input and output, and a port data
register (PDR) for storing output data.  Input or output can be assigned to individual bits.
See 2.9.2, Notes on Bit Manipulation, for information on executing bit-manipulation instructions
to write data in PCR or PDR.

Block diagrams of each port are given in Appendix C, I/O Port Block Diagrams

Table 8-1

Port Functions

Port

Description

Pins and
Functions

Other Functions

Function
Switching
Registers

Port 1

• 

8-bit I/O port

• 

MOS input pull-up option

P1

7

 to P1

5

/

IRQ

3

 to

IRQ

1

/TMIF, TMIC

External interrupts 3 to 1
Timer event interrupts
TMIF, TMIC

PMR1
TCRF,
TMC

P1

4

/

IRQ

4

/

ADTRG

External interrupt 4 and A/D
converter external trigger

PMR1,
AMR

P1

3

/TMIG

Timer G input capture input

PMR1

P1

2

, P1

1

/

TMOFH, TMOFL

Timer F output compare
output

PMR1

P1

0

/TMOW

Timer A clock output

PMR1

Port 2

*

1

• 

5-bit I/O internal port

P2

0

/SCK

1

P2

1

/SI

1

P2

2

/SO

1

SCI1 data output (SO

1

), data

input (SI

1

), clock input/output

(SCK

1

)

PMR2

P2

4

, P2

3

None

           

Summary of Contents for H8/3935










































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands