manualshive.com logo in svg

Hitachi H8/3008, Hardware Manual

Share
Download
Hitachi H8/3008 Hardware Manual Download Page 450

434

V

CC

STBY

EXTAL

φ

 (internal or

external)

RES

t

DEXT

V

IH

Figure 17.7   External Clock Output Settling Delay Timing

17.3

Duty Adjustment Circuit

When the oscillator frequency is 5 MHz or higher, the duty adjustment circuit adjusts the duty
cycle of the clock signal from the oscillator to generate 

φ

.

17.4

Prescalers

The prescalers divide the system clock (

φ

) to generate internal clocks (

φ

/2 to 

φ

/4096).

17.5

Frequency Divider

The frequency divider divides the duty-adjusted clock signal to generate the system clock (

φ

). The

frequency division ratio can be changed dynamically by modifying the value in DIVCR, as
described below. Power consumption in the chip is reduced in almost direct proportion to the
frequency division ratio. The system clock generated by the frequency divider can be output at the

φ

 pin.

Summary of Contents for H8/3008






































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands