--- 46 ---
Disassembly procedure
Disassembly
spots
Item
No.
Necessary tools
3
(1) Remove the Machine Screw M4 x 12
[276]
and remove the Nylon
Clip
[278]
from the Gear Case
[275]
(head).
(2) Remove the Seal Lock Hex. Socket Hd. Bolt M5 x 10
[150]
.
NOTE: The Seal Lock Hex. Socket Hd. Bolt M5 x 10 [150] acts as
the upper limit stopper of the Gear Case [275] (head).
Be careful that the Gear Case [275] (head) is raised by the
force of the Spring [152] when the Seal Lock Hex. Socket
Hd. Bolt M5 x 10 [150] is removed.
(3) Remove the Seal Lock Hex. Socket Set Screw M6 x 10
[64]
. Make
a flat-blade screwdriver contact with the end surface of Hinge Shaft
(A)
[186]
and lightly tap the screwdriver with a plastic hammer to
remove Hinge Shaft (A)
[186]
.
NOTE: Be sure to hold the Gear Case [275] (head) with hand
during disassembly to prevent the Gear Case [275] (head)
from being dropped when removing Hinge Shaft (A) [186]
from the hole of the Gear Case [275] (head).
Then the Spring
[152]
and the Sleeve
[151]
can be removed from
the Gear Case
[275]
(head).
(4) Remove the Seal Lock Hex. Socket Set Screw M6 x 10
[64]
and
remove Shaft (D)
[167]
from the Support
[134]
at the rear.
(5) Remove the two Hex. Socket Set Screws M8 x 10
[135]
from the
Support
[134]
at the front (operator side). Lightly tap the Support
[134]
outward with a plastic hammer to remove it from Slide Pipe
(A)
[149]
and Slide Pipe (B)
[166]
.
(6) Loosen Knob Bolt M6 x 25
[146]
at the top of Hinge (A)
[173]
and
slide Hinge (A)
[173]
to the front (operator side) to remove it from
Slide Pipe (A)
[149]
and Slide Pipe (B)
[166]
. Then slide the rear
Support
[134]
backward with Slide Pipe (A)
[149]
and Slide Pipe
(B)
[166]
mounted and remove it from Holder (A)
[145]
.
(7) Remove the Seal Lock Hex. Socket Set Screw M6 x 10
[148]
from
the side of Hinge (A)
[173]
. Remove the Bushing
[143]
from Hinge
(A)
[173]
.
NOTE: Prepare a shaft of 31 mm in diameter and 50 mm in length.
Make the shaft contact with the end surface of the Bushing
[143] and lightly tap the shaft with a plastic hammer to
remove the Bushing [143] from Hinge (A) [173].
Phillips
screwdriver
4-mm hex. bar
wrench
Flat-blade
screwdriver
Plastic hammer
Gear case,
spring, support,
hinge (A), ball
bushing, holder
(A)
3-mm hex. bar
wrench
3-mm hex. bar
wrench
4-mm hex. bar
wrench
Plastic hammer
3-mm hex. bar
wrench
Plastic hammer
φ
31 x 50 mm
shaft
Summary of Contents for C 12LSH
