--- 42 ---
Disassembly procedure
Disassembly
spots
Item
No.
Necessary tools
1
Turn table, base
ass'y
NOTE: Do not lose Spring (C) [15A] as Spring (C) [15A] pops out
when removing the Encoder [16A]. When reinstalling the
Encoder [16A] to the Turn Table [26], move the Encoder
[16A] away from Gear (A) [8] and secure it at this position
with the Machine Screw M5 x 20 [13] temporarily. Then
loosen the Machine Screw M5 x 20 [13] (about one turn)
and move the Encoder [16A] to mesh with Gear (A) [8].
(14) Remove the Machine Screw M4 x 12
[10]
and remove the Nylon
Clip
[12]
from the Turn Table
[26]
.
(15) Loosen the Clamp Lever
[156A]
and remove the two Hex. Socket
Hd. Bolts M6 x 50
[159]
to remove Stopper Holder (C)
[160]
and
Stopper (C)
[161]
from Holder (A)
[145]
.
NOTE: The head cannot be secured at the inclined position if the
Clamp Lever [156A] is removed. Be careful not to incline
the head to the left during disassembly.
(16) Incline the head to the left by 45 degrees and remove the Machine
Screw M4 x 16
[171]
to remove the Cord Cover
[169]
from Holder
(A)
[145]
. Remove the Seal Lock Hex. Socket Set Screw M6 x 10
[64]
and return the head to the right-angle position. Make a flat-
blade screwdriver contact with the end surface of the Holder Shaft
[6]
and tap the screwdriver with a plastic hammer to remove the
Holder Shaft
[6]
from the Turn Table
[26]
. Then the head can be
removed together with Holder (A)
[145]
from the Turn Table
[26]
.
NOTE: Be careful of handling the heavy head during disassembly.
(17) Turn the base upside down and remove the five Machine Screws
M5 x 20
[83]
from the back of the Turn Table
[26]
. Remove Shaft
Holder (A)
[75]
and Shaft Holder (B)
[74]
from the Turn Table
[26]
.
(18) Turn the base upside down and remove the Machine Screw
M4 x 12
[66]
to remove the Indicator
[68]
from the Turn Table
[26]
.
(19) Remove the three Flat Hd. Screws M4 x 16
[20]
and remove Gear
(A)
[19]
from the Turn Table
[26]
.
(20) Remove the six Machine Screws M5 x 16 (Black)
[60]
and remove
Table Insert (A)
[62]
and Table Insert (B)
[61]
from the Turn Table
[26]
.
(21) Remove the Shaft (B)
[23]
and remove the Turn Table
[26]
from
the Base Ass'y
[59]
.
(22) Turn the Turn Table
[26]
upside down and remove the Side Handle
[92]
to remove Shaft (A)
[91]
from the Turn Table
[26]
.
5-mm hex. bar
wrench
Phillips
screwdriver
Phillips
screwdriver
Flatblade
screwdriver
Plastic hammer
19-mm box
wrench
Summary of Contents for C 12LSH
