Hiniker DB1474A Service Manual Download | Manualshive

Page: 32 / 47

background image

TITLE

VALVE BLOCK

REMOVAL, CLEANING AND REPLACEMENT

WARNING: Always retract wings fully,
lower the plow to the ground and re-
lieve pressure before removing any

fittings, hoses or caps. Allow the system to

cool  down  before  draining  oil  or  handling
system  components.  Serious  burns  can  re-
sult  from  contact  with  hot  oil.  FAILURE  TO
HEED CAN RESULT IN SERIOUS INJURY OR
DEATH.

PHOTO NO. 9001B

Remove the three socket head cap screws using
a 3/16” allen wrench.

Carefully lift valve block off of the end head. In-

spect the five O-rings for damage. Replace as

necessary (25010762).

PHOTO NO. 4134

Make sure mating surfaces on end head and
valve block are clean and free of burrs, nicks,
etc.

Lightly oil O-rings with clean hydraulic oil and
place them on the end head.

Lay valve block flat on end head while lining up

the two locator pins. Install the three socket head
cap screws and tighten to 9-10 ft. lb. Torque us-
ing 3/16” allen wrench.

22 Valve Block Removal and Replacement

«
...
30
31
32
33
34
...
»

Summary of Contents for DB1474A
















































Reviews:

No comments

Related manuals for DB1474A

Brand: Sabaj Pages: 12

Brand: National Instruments Pages: 15

Brand: National Instruments Pages: 20

Brand: National Instruments Pages: 22

NI PXI-665 Series

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 30

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 34

Brand: WAGO Pages: 18

Brand: WAGO Pages: 46

Brand: Skov Pages: 68

Brand: GRAUPNER Pages: 180

Brand: Kenco Pages: 15

Brand: Miller Electric Pages: 18

Hammerfall DIGI9652

Brand: RME Audio Pages: 22

Brand: Lutron Electronics Pages: 36

Brand: ITR Pages: 15

PRO-CRAFT240 MIG

Brand: Uni-Mig Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands