Hiniker DB1474A Page 23 Service Manual Download | Manualshive

Page: 23 / 47

background image

TITLE

DC MOTOR REMOVAL AND REPLACEMENT

WARNING: Disconnect Vehicle Battery
prior to performing this procedure to
avoid electrical shock or burns.

1

2

PHOTO NO. 8996A

Disconnect the black wire of the battery power
cable at location 2. Disconnect the red (or red
striped) wire of the battery power cable from the
motor terminal at location 1.

MOUNT BOLTS

PHILLIPS HEAD SCREWS

MOTOR CAP

MOTOR

DWG NO. 3512

Remove the two Phillips head screws from the
motor cap. Using a 3/8” wrench loosen the two
motor mounting bolts. Do not remove bolts.

NOTE:

Use care when removing the motor from

the endhead, the motor can separate into three
pieces and will require additional time to reas-
semble.

Hold motor together while removing it from the
end head.

NOTE:

If oil is found in the cavity of the valve

passage where the coupling is located, replace-
ment of the oil pump shaft seal is necessary be-
fore the unit can be put back into service. See
page 23.

PHILLIPS HEAD SCREWS

MOTOR CAP

MOTOR

MOTOR TERMINAL

(POS)

GROUND SCREW

(NEG)

COUPLING

PUMP SHAFT

VALVE PASSAGE

SHIPPING NUTS
(REMOVE)

DWG NO. 3513

Remove  shipping  nuts  from  new  motor,  align
splined shaft of motor with coupler and position
motor  onto  the  locating  pins  on  the  end  head.
Torque  the  two  motor  mounting  bolts  to  5-8  ft.
lbs.  with  a  3/8”  wrench.  Reattach  motor  cap.
Reconnect  the  black  wire  of  the  battery  power
cable  at  location  2  and  the  red  (or  red  striped)
wire  of  the  battery  power  cable  to  motor  termi-
nal at location 1. See photo 8996A.

DC Motor Removal and Replacement 13

«
...
21
22
23
24
25
...
»

Summary of Contents for DB1474A
















































Reviews:

No comments

Related manuals for DB1474A

Brand: Vancare Pages: 31

Brand: TCS Pages: 16

Brand: Elettro CF Pages: 24

Brand: MLR Pages: 5

Brand: zika Pages: 13

Brand: SPT Pages: 32

Brand: Lincoln Electric Pages: 46

Brand: Radiant Pages: 82

Brand: Clarke Pages: 16

Brand: Lincoln Electric Pages: 23

Autoscript WHC-IP A9009-0005

Brand: Vitec Multimedia Pages: 20

Brand: FY-TECH Pages: 19

Brand: Norco Pages: 2

Brand: Unitor Pages: 32

Brand: Mi-Light Pages: 5

Brand: iSMA Pages: 107

Starmig 180 Dual Synergic

Brand: Blueweld Pages: 18

Brand: Faraone Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands