manualshive.com logo in svg

Hiniker DB1474A, Service Manual, Page: 19 / 47

Share
Download
Hiniker DB1474A Service Manual Download Page 19

TITLE

LEFT WING WILL NOT STAY EXTENDED

Perform all initial inspections and checks listed on page 1 before beginning test procedure.

WARNING: Always retract wings fully, lower the plow to the ground and relieve pressure 

before removing any fittings, hoses or caps. Allow the system to cool down before drain

-

ing oil or handling system components. Serious burns can result from contact with hot 
oil. FAILURE TO HEED CAN RESULT IN SERIOUS INJURY OR DEATH.

LEFT WING WILL NOT STAY EXTENDED
ALL OTHER FUNCTIONS ARE NORMAL.

Remove, inspect and clean Check Valve 1 (CV1).

See page 15.

Repair or replace as necessary.

DOES LEFT WING STAY EXTENDED?

Remove, inspect and clean
S2 Solenoid Valve. See page 20.
Repair or replace as necessary.

Does Left Wing Stay Extended?

Yes

No

Call Hiniker Service

Yes

No

End

Remove, inspect and clean Relief Valve 
1 (RV1). See page 18. Repair or replace 
as necessary. Reinstall and adjust.
See page 31.

Does Left Wing Stay Extended?

Yes

No

End

Left Wing Will Not Stay Extended   9

Summary of Contents for DB1474A
















































Reviews:

No comments