Hiniker DB1474A Page 33 Service Manual Download | Manualshive

Page: 33 / 47

background image

TITLE

Hydraulic Pump Replacement 23

HYDRAULIC PUMP

REMOVAL, CLEANING AND REPLACEMENT

WARNING: Always retract wings fully,
lower the plow to the ground and re-
lieve pressure before removing any

fittings, hoses or caps. Allow the system to

cool  down  before  draining  oil  or  handling
system  components.  Serious  burns  can  re-
sult  from  contact  with  hot  oil.  FAILURE  TO
HEED CAN RESULT IN SERIOUS INJURY OR
DEATH.

SCREW

RESERVOIR

BREATHER

DWG NO. 3518

Remove  breather  from  reservoir  and  carefully
drain  oil  from  the  reservoir  into  a  suitable  con-
tainer.  Remove  the  four  retaining  screws  from

the reservoir with a 1/4” wrench.

PHOTO NO. 9007

Remove the reservoir while unit is lying flat on

a table. Using a rubber mallet, tap lightly on the
side of the reservoir.

Remove return line filter by pulling it straight off

the return tube. The filter should be replaced

with a new one (P/N 25010745).

Remove return line by loosening the compres-

sion fitting.

NOTE:

There is a compression sleeve on the re-

turn tube behind the fitting. Care should be taken

not to lose sleeve.

Remove the inlet filter by pulling it straight off

the barbed end of the plumbing elbow. The fil

-

ter should be replaced with a new one. (P/N
25010221).

PHOTO NO. 9007A

Remove the bolts from suction cover. Remove
suction cover.

«
...
31
32
33
34
35
...
»

Summary of Contents for DB1474A
















































Reviews:

No comments

Related manuals for DB1474A

Century 2 NCL10000 Series

Brand: BraunAbility Pages: 39

Brand: elsner elektronik Pages: 148

Power2 S-MIG 100

Brand: STAMOS Pages: 33

CoolBloC C34 DN 32

Brand: PAW Pages: 24

BLUEBOX ADVANT UHF

Brand: iDTRONIC Pages: 54

Brand: B&B Molders Pages: 18

Brand: Keurig Pages: 6

Brand: Elektron Pages: 32

Brand: Gage Pages: 36

Brand: AXEM Technology Pages: 31

Brand: Feig Electronic Pages: 35

Brand: Ingersoll-Rand Pages: 64

Brand: Madas Pages: 40

Brand: stertil Pages: 39

Brand: White Knight Pages: 20

Brand: ActSafe Pages: 70

Brand: ims PRO Pages: 114

PIPELINER 200D KUBOTA

Brand: Lincoln Electric Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands