Hiniker DB1474A Page 27 Service Manual Download | Manualshive

Page: 27 / 47

background image

TITLE

SYSTEM RELIEF VALVE

REMOVAL,CLEANING AND REPLACEMENT

WARNING: Always retract wings fully,
lower the plow to the ground and re-
lieve pressure before removing any

fittings, hoses or caps. Allow the system to

cool  down  before  draining  oil  or  handling
system  components.  Serious  burns  can  re-
sult  from  contact  with  hot  oil.  FAILURE  TO
HEED CAN RESULT IN SERIOUS INJURY OR
DEATH.

PHOTO NO. 4127

Remove the cap with a 1” wrench.

Remove the valve adjustment screw with a
straight slot screwdriver. Remove spring.

Remove the ball with a pencil magnet. Inspect
the spring, ball, and seat in the valve block for
contamination, distortion, or wear.

Flush out valve block with clean hydraulic oil.

BALL

O-RING

SPRING

ADJ. SCREW

VALVE CAP

DWG NO. 3516

Re-install the ball, spring and adjustment screw.
The adjustment screw should be turned in ap-
proximately 2 full turns.

Check O-ring in cap for cuts and replace as nec-
essary. (P/N 25010518).

Install cap, ensuring that the O-ring is in cap
groove. Tighten cap with 1” wrench.

Adjust relief pressure. See “System Relief Valve,
Testing and Adjustment.” Page 29.

System Relief Valve Removal, Cleaning & Repacement 17

«
...
25
26
27
28
29
...
»

Summary of Contents for DB1474A
















































Reviews:

No comments

Related manuals for DB1474A

Brand: Eaton Pages: 4

Brand: Eaton Pages: 10

Aqua-Hot AHE-100-04S

Brand: Vehicle Systems Pages: 19

Brand: WAGO Pages: 56

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

BrewZilla 100L - Gen 4

Brand: KegLand Pages: 48

Brand: Genie Pages: 202

SAF-FRO PRESTOTIG 240 AC/DC

Brand: Air Liquide Pages: 121

Brand: Ravaglioli Pages: 72

Brand: Neilsen Pages: 9

Brand: Holzmann Pages: 23

RM-208 CB.13.01

Brand: EasyLine Pages: 16

HRU-WALL-RC Series

Brand: Nalnor Pages: 32

Brand: Weldability Pages: 12

Brand: Jet Pages: 40

Brand: National Instruments Pages: 297

Brand: Kühtreiber Pages: 44

Brand: Yaesu Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands