background image

20

English

10 Disposal

WARNING

Risk of injury.

Hazards presented by improper disposal.

Improper disposal of the equipment may have the following consequences:

The burning of plastic components generates toxic fumes which may present

a health hazard. Batteries may explode if damaged or exposed to very high

temperatures, causing poisoning, burns, acid burns or environmental pollution.

Careless disposal may permit unauthorized and improper use of the equipment.

This may result in serious personal injury, injury to third parties and pollution of

the environment.

Dispose of defective batteries right away. Keep them out of reach of children.

Do not disassemble or incinerate the batteries.

Batteries that have reached the end of their life must be disposed of in accordance

with national regulations or returned to

Hilti

.

Most of the materials from which

Hilti

tools and appliances are manufactured can

be recycled. The materials must be correctly separated before they can be recycled.

In many countries, your old tools, machines or appliances can be returned to

Hilti

for

recycling. Ask

Hilti

Service or your Hilti representative for further information.

Disposal of electric tools or appliances together with household waste is not

permissible.

11 Manufacturer’s warranty

Please contact your local

Hilti

representative if you have questions about the warranty

conditions.

12 FCC statement (applicable in US) / IC statement (applicable in Canada)

The product complies with part 15 of the FCC Rules and RSS­210 of the IC.

Operation is subject to the following two conditions:
• This device shall cause no harmful interference.

• This device must accept any interference received, including interference that may

cause undesired operation.

Note

Changes or modifications not expressly approved by

Hilti

can restrict the user’s

right to operate the device.

Printed: 04.10.2017 | Doc-Nr: PUB / 5377202 / 000 / 01

Summary of Contents for BX 3-ME

























Reviews: