manualshive.com logo in svg

Hilti BX 3-ME, Operating Manual

Share
Download
Hilti BX 3-ME Operating Manual Download Page 11

English

9

3.5 Bluetooth

The product has a Bluetooth interface. Wireless communication via Bluetooth is possible

as soon as the battery has been fitted and the fastening tool switched on at the on/off

button.

Data transfer continues for three hours after the tool has switched to standby mode or

after the tool has been switched off at the on/off button.

To deactivate Bluetooth manually, press and hold down the on/off button for at least 5

seconds until the LED shows blue twice.

When the battery is removed, no further data are transferred.

3.6 Status indicator

The status indicator provides information about the status of the fastening tool.

Status

Meaning

Off

• The fastening tool is switched off

The LED shows green.

• The fastening tool is switched on and

ready for use

The LED flashes green every 3 seconds.

• The fastening tool is in stand-by mode.

Press the nose of the tool against the

working surface to switch it on

The LED flashes green.

• The fastening tool is too hot or the

battery has insufficient power; see

“Troubleshooting”

The LED flashes red.

• Malfunction; see “Troubleshooting”

The LED shows red.

• Malfunction; see “Troubleshooting”

3.7 Indication of battery charge status

When one of the battery release buttons is pressed the display indicates the battery’s

state of charge.

Note

Reliable indication of the charge status is not possible while a fastener is being

driven or immediately after a fastener is driven.

Status

Meaning

All four LEDs light green.

• Charge status is 75 % to 100 %.

Three LEDs light green.

• Charge status is 50 % to 75 %.

Two LEDs light green.

• Charge status is 25 % to 50 %.

One LED lights green.

• Charge status is 10 % to 25 %.

One LED blinks green.

• Charge status is below 10 %. The tool

is ready for use.

3.8 Batteries

Battery performance drops at low temperatures.

When battery performance drops, it takes longer (than with a fully charged battery) until

the fastening tool is ready to drive the next fastener.

If you continue to operate the fastening tool after battery performance drops, the fastening

tool will switch itself off automatically before damage to the battery occurs.

Printed: 04.10.2017 | Doc-Nr: PUB / 5377202 / 000 / 01

Summary of Contents for BX 3-ME

























Reviews:

No comments

Brands by name

Popular brands

Load more brands