manualshive.com logo in svg

Hillrom 900 Series, Instructions For Use Manual

Share
Download
Hillrom 900 Series Instructions For Use Manual Download Page 83

171051(12) - Hillrom™ 900 Electric Bed Instructions for Use

Page 77

De
contamina

tio

n

M

aintenanc

e

Recommended Materials and Products

NOTE:

A list of recommended cleaning products for all types of cleaning requirements 

is available on your request along with a special maintenance advice leaflet.

• Single-use tissues or recyclable textile wipers.
• One pair of household gloves.
• Detergent-disinfectant solution diluted according to hospital guidelines (and 

taking into account the recommendations given below) or a disinfecting 
spray.

• Use a product that complies with standard EN 14885 (bactericide including 

TB, fungi and viruses, including HIV-1 and HBV).

• Chlorine (26,000ppm) solution that complies to EN 13727 and EN 13624 can 

be used, but has the risk of discoloration. Non coated metal parts should be 
rinsed to prevent pitting corrosion.

The following products should not be used

Formaldehyde, or phenol-based products and solvents of any kind (toluene, 
xylene or acetone).
Never use abrasives, cleaning powder or cleaning pads that may damage 
components.

Recommended Cleaning and Disinfection Method

• Always wipe downward, working from the cleanest to the dirtiest areas.
• Do not scrape surfaces.
• Keep wipes damp (wet as many times as needed and do not wring out too 

much water).

• Let product dry according to disinfectant manufacturer's recommendations to 

ensure maximum efficiency.

• Rinse if necessary: follow the recommendations of the disinfectant supplier.
• Change wipes when cleaning the least contaminated areas to areas of 

medium or to highly contaminated areas.

• Change wipes when cleaning another bed.
• Always dry the bed thoroughly after it has been cleaned.

Cleaning tough stains

Quickly wipe away any traces of pharmaceutical solutions or other staining 

products, in order to avoid permanent damage to the surface.

To remove tough stains, use standard household cleaners and a soft bristle brush. 
To loosen heavy, dried-on soil or excreta, you may first need to saturate the spot.

Summary of Contents for 900 Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands