manualshive.com logo in svg

Hillrom 900 Series, Instructions For Use Manual

Share
Download
Hillrom 900 Series Instructions For Use Manual Download Page 70

Page 64

171051(12) - Hillrom™ 900 Electric Bed Instructions for Use

Oxygen Cylinder Holder (AC959A-AD101A-AD102A)

Safe working load: 15 kg

(1)

The oxygen cylinder holder is designed to accept an oxygen cylinder and must 
only be fitted on the patient helper supports at the head end of the bed outside the 
sleep surface. It can be rotated through 80°. Each type of holder corresponds to a 
cylinder model and must never be used with a different cylinder. See below.

AC959A for 

cylinder model 

B5 (Ø140)

AD101A for 

cylinder model D 

(Ø100)

AD102A for 

cylinder model E 

(Ø100)

The following recommendations are designed to prevent any possible incidents so that 
this accessory can be used in optimum safety conditions for both the patient and 
nursing staff.

• Check that the cylinder is correctly 

positioned at the base of the cylinder 
holder.

• Never use a different oxygen cylinder 

model from the model that is specified 
above (danger of dropping the cylinder 
or interfering with various operations 
could occur).

• Prevent any impact when moving a 

bed equipped with a cylinder holder 
(especially doorways). 

• If the cylinder holder does not allow 

the bed to go through a doorway, 
position the holder in front of the bed, 
otherwise place it and the cylinder on the mattress (remember to put the 
holder in its normal position after moving the bed).

1. The safe working load specifications allow for a substantial safety margin.

Summary of Contents for 900 Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands