manualshive.com logo in svg

HIKVISION DS-K3B801SX Series, Quick Start Manual

Share
Download
HIKVISION DS-K3B801SX Series Quick Start Manual Download Page 8

• Please keep all wrappers after unpack them for future use. In case of any failure occurred, you

need to return the device to the factory with the original wrapper. Transportation without the

original wrapper may result in damage on the device and lead to additional costs.

• Improper use or replacement of the battery may result in hazard of explosion. Replace with the

same or equivalent type only. Dispose of used batteries according to the instructions provided by

the battery manufacturer.

• Biometric recognition products are not 100% applicable to anti-spoofing environments. If you

require a higher security level, use multiple authentication modes.

• Do not stay in the lane when the device is rebooting.

• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED

BATTERIES ACCORDING TO THE INSTRUCTIONS.

• SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

• The instructions shall require connection of the equipment protective earthing conductor to the

installation protective earthing conductor.

DS-K3B801SX Series Swing Barrier Quick Start Guide

vii

Summary of Contents for DS-K3B801SX Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands