manualshive.com logo in svg

HIKVISION DS-K3B801SX Series, Quick Start Manual

The HIKVISION DS-K3B801SX Series product comes with a comprehensive Quick Start Manual, allowing users to easily set up and operate the device. To quickly access the manual, download it for free from manualshive.com. Enhance your experience with this user-friendly product by referring to the detailed instructions provided in the manual.

Share
Download
background image

Note

For details, see Disassemble Side Base Cover .

Figure 5-5 Network Switch Position

2. Lead out 12 V power supply from the main switch and connect it to the network switch's power

interface.

3. Connect the network cable with the network switch.

5.5 Face Recognition Terminal Power Supply Wiring

You should wire the power supply terminal on the 12 V power supply component if you connect

the turnstile to the face recognition terminal.
The terminal's position is shown as follows:

DS-K3B801SX Series Swing Barrier Quick Start Guide

29

Summary of Contents for DS-K3B801SX Series









































































Reviews:

No comments

Related manuals for DS-K3B801SX Series

Brands by name

Popular brands

Load more brands