manualshive.com logo in svg

HIKVISION DS-K3B801SX Series, Quick Start Manual

The HIKVISION DS-K3B801SX Series product comes with a comprehensive Quick Start Manual, allowing users to easily set up and operate the device. To quickly access the manual, download it for free from manualshive.com. Enhance your experience with this user-friendly product by referring to the detailed instructions provided in the manual.

Share
Download
background image

Figure 5-6 Face Recognition Terminal Power Supply Wiring Position

5.6 Terminal Description

The lane controller contains main lane controller and sub lane controller, which controls the IR

beams, motor, and other components' work.

5.6.1 Main Control Board Terminal Description

The main lane control board contains power supply interface, supercapacitor interface, brake

interface, motor drive interface, light board interface, motor encoder interface, door open position

detection interface, debug port, lane communication interface, interconnecting interface, and DIP

switch (reserved).
The picture displayed below is the main control board diagram.

DS-K3B801SX Series Swing Barrier Quick Start Guide

30

Summary of Contents for DS-K3B801SX Series









































































Reviews:

No comments

Related manuals for DS-K3B801SX Series

IPC 1012M/DS Instruction Manual preview
1012M/DS
Brand: IPC Pages: 84
Next Systems ALLAR0415 B 56 Technical Manual preview
ALLAR0415 B 56
Brand: Next Systems Pages: 8

Brands by name

Popular brands

Load more brands