HIKVISION DS-K3B801SX Series Page 12 Quick Start Manual Download

Page: 12 / 72

Chapter 1 Overview

1.1 Introduction

The swing barrier with two barriers and 24 IR lights is designed to detect unauthorized entrance or

exit. By adopting the swing barrier integrated with the access control system, person should

authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely

used in attractions, stadiums, construction sites, residences, etc.

1.2 Main Features

• 32-bit high-speed processor

• TCP/IP network communication

The communication data is specially encrypted to relieve the concern of privacy leak.

• Permissions validation and anti-tailgating

• Remaining open/closed mode selectable

• Bidirectional (Entering/Exiting) lane

The barrier opening and closing speed can be configured according to the visitor flow.

• The barrier will be locked or stop working when people are nipped

DS-K3B801SX Series Swing Barrier Quick Start Guide

Summary of Contents for DS-K3B801SX Series









































































Search results

Summary of Contents for DS-K3B801SX Series

Reviews:

Related manuals for DS-K3B801SX Series

Brands by name

Popular brands

HIKVISION DS-K3B801SX Series, Quick Start Manual

Search results

Summary of Contents for DS-K3B801SX Series

Reviews:

Related manuals for DS-K3B801SX Series

Brands by name

Popular brands