manualshive.com logo in svg

HIKVISION DS-K3B801SX Series, Quick Start Manual

Share
Download
HIKVISION DS-K3B801SX Series Quick Start Manual Download Page 46

5.6.4 Access Control Board Serial Port ID Description

You can use the jumper cap on the access control board to switch the interface communication

mode. For details about switching between RS-232 and RS-485 communication type, see Switching

RS-485/RS-232 Mode.

Figure 5-10 Access Control Board

According to the picture above, the RS-485 serial port corresponds to UART2 and UART3. RS-232

serial port is corresponded to UART7 and UART8. Wiring Interface is corresponded to UART1,

UART4, UART6, UART6, and Lane.
The access control board descriptions are as follows:
UART2/UART3 Jumper Cap

Reserved serial port. Use the jumper cap to switch the serial port communication mode. You

can switch between the RS-485 communication mode and the RS-232 communication mode. By

default, it is in RS-485 communication mode.

UART6 Jumper Cap

Use the jumper cap to switch the serial port communication mode with the sub lane controller.

You can switch between the RS-232 communication mode and the RS-485 communication

mode. By default, it is in RS-232 communication mode.

UART5 Jumper Cap

Use the jumper cap to switch the serial port communication mode with the sub lane controller.

You can switch between the RS-485 communication mode and the RS-232 communication

mode. By default, it is in RS-485 communication mode.

UART1 Jumper Cap

Use the jumper cap to switch the serial port communication mode with the main lane

controller. You can switch between the RS-485 communication mode and the RS-232

communication mode. By default, it is in RS-485 communication mode.

Lane

DS-K3B801SX Series Swing Barrier Quick Start Guide

35

Summary of Contents for DS-K3B801SX Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands