HIKVISION DS-K3B801SX Series Quick Start Manual Download

Page: 5 / 72

under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive

2011/65/EU
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed

of as unsorted municipal waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of equivalent new equipment,

or dispose of it at designated collection points. For more information see:

www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product

documentation for specific battery information. The battery is marked with this

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated

collection point. For more information see:www.recyclethis.info

DS-K3B801SX Series Swing Barrier Quick Start Guide

Summary of Contents for DS-K3B801SX Series









































































Search results

Summary of Contents for DS-K3B801SX Series

Reviews:

Related manuals for DS-K3B801SX Series

Brands by name

Popular brands

HIKVISION DS-K3B801SX Series, Quick Start Manual

Search results

Summary of Contents for DS-K3B801SX Series

Reviews:

Related manuals for DS-K3B801SX Series

Brands by name

Popular brands