HIKVISION DS-8100-S Series User Manual Download Page 61

Page: 61 / 98

HIKVISION DS-8100-S User‟s Manual

• IP Address:

IP address you would like to use for your DVR.

• Subnet Mask:

Subnet Mask of network.

• Default Gateway:

IP address of your Gateway. Typically the IP address of your router.

• Preferred/Alternate DNS Server:

The preferred and alternate Domain Name System (DNS) Server

to be used with your DVR.

Click OK to save and exit the Network Settings menu.

Configuring PPPoE Settings

Your DVR also allows for Point-to-Point Protocol over Ethernet (PPPoE) access. To set up PPPoE access:

Enter the Network Settings menu by clicking Menu > Setting > Network.

Select the

General

tab.

Set the IP address and subnet mask to 0, as shown in Figure 3. When the PPPoE connection is
successfully established, the IP address will be added automatically.

Figure 3. Network Settings Menu

Select the

Advanced

tab. This will take you to the advanced network settings menu, shown in Figure

Figure 4. Advanced Network Settings

Summary of Contents for DS-8100-S Series



































































































Search results

Summary of Contents for DS-8100-S Series

Reviews:

Related manuals for DS-8100-S Series

Brands by name

Popular brands

HIKVISION DS-8100-S Series, User Manual

Search results

Summary of Contents for DS-8100-S Series

Reviews:

Related manuals for DS-8100-S Series

Brands by name

Popular brands