manualshive.com logo in svg

HIKVISION DS-8100-S Series, User Manual

Share
Download
HIKVISION DS-8100-S Series User Manual Download Page 35

HIKVISION DS-8100-S User‟s Manual 

35 

 

 

 

 

Figure 9. HDD Property Settings Menu 

 

 

5.

 

Set HDD to Read-Only. 

6.

 

Click the OK button. The HDD is now read-only. 

 

Note:

 

When a HDD is set to 

read-only

, no more recordings can be written to the disk. In order to enable recordings 

on that particular disk again, you must set the HDD to R/W (Read/ Write) in the HDD Property Settings menu. If 
multiple HDDs are used, the DVR will automatically record to the next HDD that is not set to 

read-only

. 

Configuring Advanced HDD Settings

 

Setting up HDD Redundancy

 

To insure unexpected failures of hard disk drives, it‟s recommended to set up HDD redundancy. It is important to note 
that in order to set up HDD redundancy, you‟ll need more than one HDD in your DVR. 
 
To set up HDD redundancy: 
 

1.

 

Navigate to the HDD Management menu by clicking Menu > HDD management. 

2.

 

Click on the 

General 

tab. 

3.

 

Select the HDD to be used for redundancy, as shown in Figure 10.

 

 

Summary of Contents for DS-8100-S Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands