HIKVISION DS-8100-S Series User Manual Download

Page: 80 / 98

HIKVISION DS-8100-S User‟s Manual

Figure 2. HDD Group Settings Menu

Select OK to save and exit menu.

Note:

By default, all HDDs belong to group 1.

Setting HDD Status

You may change the behavior of your HDD by changing its status. The status of a HDD can be set to redundancy,
read-only or read/write (R/W).

Setting HDD to Read-Only

A HDD can be set to read-only to avoid important recorded files from being overwritten when the HDD becomes full.

To set a HDD to read-only:

Enter the HDD Management menu by clicking Menu > HDD.

Select HDD to protect.

Select the Property button to enter the Property Settings menu, as shown in Figure 3.

Figure 3. HDD Property Settings Menu

Summary of Contents for DS-8100-S Series



































































































Search results

Summary of Contents for DS-8100-S Series

Reviews:

Related manuals for DS-8100-S Series

Brands by name

Popular brands

HIKVISION DS-8100-S Series, User Manual

Search results

Summary of Contents for DS-8100-S Series

Reviews:

Related manuals for DS-8100-S Series

Brands by name

Popular brands