manualshive.com logo in svg

HIKVISION DS-6500DI-T, User Manual, Page: 4 / 54

Share
Download
HIKVISION DS-6500DI-T User Manual Download Page 4

User Manual of DS-6500DI–T Universal Network Decoder   

3 

Preventive and Cautionary Tips

 

Before connecting and operating your decoder, please be advised of the following tips: 

•

 

Ensure unit is installed in a well-ventilated, dust-free environment. 

•

 

Keep all liquids away from the decoder.  

•

 

Please check the power supply to avoid the damage caused by voltage mismatch. 

•

 

Please make sure the decoder work in the allowed range of temperature and humidity. 

•

 

Please keep the device horizontal and avoid the installation under severe vibration environment. 

•

 

The dust board will cause a short circuit after damping; Please remove dust regularly for the board, connector, 

chassis fan and other parts of the device with brush.  

•

 

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent 

type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.  

 

 

 

Summary of Contents for DS-6500DI-T























































Reviews:

No comments