HIAB 410K PRO Operator'S Manual Download Page 72 | Manualshive

Page: 72 / 82

HIAB 410K PRO Operator'S Manual Download Page 72

Environmentally friendly oil

The environmentally friendly oils recommended for HIAB products are ester based synthetic
hydraulic fluids (synthetic ester).

CAUTION

Vegetable oils do not meet Hiab requirements and must not be used.

After filling the tank

1. Operate each crane function to its end positions.
2. Operate the crane to parked position.
3. Check and top up the oil tank to max level on the tank gauge.
4. Bleed the air from the hydraulic system.

8.6. Replacement of filters

Filter cartridges must be replaced by a Hiab authorised service workshop:

• After the first 50 hours operation
• Then after every 1000 hours operation
• Or at least once a year.

How do you verify if the filter needs a replacement?

The high pressure filter is on the crane base, connected to
the pressure line from the pump. It has an indicator (1) that
turns red when the replacement is needed.

The  return  oil  filter  is  on  the  oil  tank,  and  can  have  a
clogging indicator. This indicator turns red when needed. In
all  other  cases  (if  the  filter  time  is  expired  or  without
clogging  indicator),  you  must  follow  the  general
recommendations for its replacement.

There are other filters on your crane (the pressure-reducer filter (1) on remote-controlled cranes,
and the breathing filter (2) on the oil tank). These filters have no indicator and you must follow the
general recommendations for their replacement.

Maintenance and Service

72

HIAB 410K PRO

«
...
70
71
72
73
74
...
»

Summary of Contents for 410K PRO



















































































Reviews:

No comments