manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 13 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 13

2.7. LHV Load holding valves

All  cylinders  are  equipped  with  load-holding  valves  as  a
safety device. After a crane movement, they hold the crane
in position, also in the unlikely event of a burst hose.

If there is a leak or a component fractures, such as a pipe,
hose  or  coupling,  the  load-holding  valves  will  stop  the
booms  from  collapsing  down,  even  when  the  hydraulic
system is switched off, and you operate a particular crane
lever.

To  operate  a  hydraulic  cylinder  equipped  with  a  load
holding valve, an opening pressure is required.

2.8. Description of HIAB 410K Pro

The HIAB 410K Pro are compact, fully hydraulically operated goods cranes.

Stress history class S1 according to EN 13001-1.

Lifting capacity:

• HIAB 410K = 29.7 tonne metres (214800 lbs.ft)

The cranes are supplied in a version:

• HIAB 410K-3 reach: 22.5 metres (73' 9" ft)

The  main  control  valve  V91  and  the  SPACE  3000  safety  system  are  standard  equipment  on  the
HIAB 410K Pro.

The crane type and the manufacturer are marked on the serial number plate.

NOTE

The exact technical information for your crane is shown in the Technical Data.

Structure and parts of the crane

HIAB 410K PRO

13

Summary of Contents for 410K PRO



















































































Reviews:

No comments