manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 63 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 63

• Do a check of the LEDs on the User Interface.

LED Test on the UI box:

1. Push the ON/OFF button for at least 2 seconds. The test is activated and all the red LEDs

are illuminated. If the system is equipped with warning lights / lamp poles, all the lights will
come on.

2. Release the button. After 3 sec, all the green LEDs are illuminated. The test is finished when

all LEDs are off.

Hydraulic system and oil level in the tank

• Check that there are no leaks from the hydraulic hoses, lines and connections.
• Make sure that all security seal wires (Ex. LHV, dump valves, etc...) are not broken. Always go

to/contact a Hiab authorised service workshop when the seal wire has been broken.

• Check oil level in the tank. If necessary, fill to correct level.

NOTE

Always place the vehicle on level ground
with the crane in transport position while
checking the oil.

Oil level on the slewing housing

• Do a check of the oil level in the slewing housing. If necessary, fill to correct level.

Filters

• Check the filter indicator. If red, a workshop must replace the cartridge.

Maintenance and Service

HIAB 410K PRO

63

Summary of Contents for 410K PRO



















































































Reviews:

No comments