manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 14 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 14

3. Safety precautions and warnings

3.1. Operating conditions

You may use the crane ONLY if:

• You are outdoors or in a space with sufficient ventilation.
• With  a  mean  wind  velocity  of  less  than  13.3  m/sec  (approx.  29.7  mph). 

See  the  wind  speed

table.

DANGER

•

Do not use

 the crane in a confined space because you could suffocate from the

exhaust gases from the vehicle.

•

Never 

use  the  crane  in  a  high  wind  or  storm.  When  the  mean  wind  velocity

exceeds  13.3  m/sec  (approx.  29.7  mph)  the  crane  will  behave  unpredictably.

Never

 use the crane during a thunderstorm.

•

Never

  use  the  crane  at  temperatures  below  -30°C  (-22°F),  as  the  steel's

properties deteriorate below this temperature.

WARNING

• At temperatures below 0°C (32°F), do not

touch  the  operating  levers  during  the  first
few minutes.

• In cold weather, the wear on the hydraulic

system  is  greater  than  at  normal  working
temperatures.

In cold weather, start the crane as follows:

• Engage the power take-off at low rpm.
• Allow the system to idle for a few minutes.
• Operate  stabiliser  legs  up  and  down  for

one minute, in order to warm up the oil.

Safety precautions and warnings

14

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Reviews:

No comments