manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 32 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 32

3.5.4. Use of lifting equipment

DANGER

• Only  use  lifting  accessories  that  are  suitable  for  your  crane.  Contact  a  HIAB

service workshop.

• Never attempt to install add-on lifting accessories yourself!
• Add-on lifting accessories may only be installed by an authorised HIAB service

workshop.

• When  using  lifting  accessories,  follow  the  instructions  supplied  with  the

equipment!

• Watch out for hazards!
• Never try to adjust lifting accessories when you are working on the crane!

After the lifting accessories have been fitted:

1. Check that the lifting accessories are securely fixed.
2. Only after this should you use your crane.

WARNING

• Clean the couplings, when connecting and disconnecting lifting accessories. Dirt

can damage the hydraulic system.

• Take care that your fingers are not trapped

3.5.5. Use of demountable cranes

DANGER

• Make  sure  that  there  are  no  unauthorised  persons  in  the  immediate  vicinity  of

the  crane.  When  mounting/demounting  the  crane  on/from  the  vehicle,  people
can suffer fatal crushing injuries!

• After setting up, verify that the crane is properly locked!

WARNING

Be  careful  when  mounting/demounting  the  crane  on/from  the  vehicle  as  rough
handling can seriously damage the crane or the vehicle.

Safety precautions and warnings

32

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Reviews:

No comments