manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 43 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 43

5.2. Stabiliser system and ground conditions

Always:

• Make sure that the ground can support the load that the

stabiliser leg imposes on the ground.

 (*)

• Make sure that the ground is not undermined.
• Use  the  extra  support  plates  that  are  large  and  firm

enough for your crane model.

The  maximum  permitted  ground  inclination  under  the
stabiliser leg plate is 5º.

(*) The maximum load (P) that the stabiliser leg can apply to the ground is (kN):

Crane Model

Stabiliser leg config.

Short

Medium

Long

Extra long

265-285

200

200

-

-

395-425-505-335K-410K-435K

230

230

-

-

322-377-328-352-362-388

230

200

180

-

422-477 

Medium stab. exten.

220

220

-

-

Long stab. exten.

240

240

-

-

Extra long stab. exten.

220

220

-

-

358-398-408-418

230

200

180

-

528-548-558-638-658

-

250

250

-

858-1058

370

370

370

370

HIAB Auxiliary stabilisers

180

NOTE

Sign that shows the maximum force that the stabiliser
legs can apply to the ground.

Starting crane operation

HIAB 410K PRO

43

Summary of Contents for 410K PRO



















































































Reviews:

No comments