manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 42 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 42

Engage the PTO

Engage the PTO (Power Take Off) and bring the vehicle engine to the correct rpm.

NOTE

• Rpm too high: the oil in the hydraulic system might overheat.
• Rpm too low: during crane operation, the vehicle engine could stall.
• The maximum rpm may depend upon a governor on your PTO combination.

CAUTION

Close the driver’s cab to prevent access to unauthorised persons.

Start the safety system

The operating levers must be in the neutral position before
start up.

To start the safety system, press the On/Off button  . The
LED  above  the  button  lights  up.  The  system  will  check
itself. (2-4 seconds) .

Manual controlled stabiliser extensions and legs

When in manual operation:

1.

On the side where the stabiliser extension and leg will

be operated, press the button   to activate.

2.

Go  to: 

Extend  stabiliser  extensions  and  set

stabiliser legs

SPACE 3000

SPACE 3000

Starting crane operation

42

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Reviews:

No comments