HIAB 410K PRO Operator'S Manual Download Page 67

Page: 67 / 82

x 2

8.4.2. Greasing the upper column bearing and three-point bridge

DANGER

The upper column bearing must be grease while the crane is slewed.

NOTE

The lubrication points can be fitted differently than showed in the image.

Grease through the nipples in the greasing manifold,
located on the crane base, according to the greasing signs.
If the manifold does not exist, grease directly through the
nipples, located on the upper column bearing.

Niples (1): For greasing upper column bearing

Niple (2): For greasing three-point bridge

If you are greasing the upper column bearing without
help:

1. Grease the upper bearing with a little grease.
2. Slew the crane a little.
3. Grease it again and repeat until the column has

completed one turn.

If you are greasing the upper column bearing with help:

One person greases the upper column bearing, while another carefully slews the crane.

➀ ➁

Maintenance and Service

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Search results

Summary of Contents for 410K PRO

Reviews:

HIAB 410K PRO, Operator'S Manual, Page: 67 / 82

Search results

Summary of Contents for 410K PRO

Reviews: