background image

X

4

 

SUPPLY AIR 

TEMP

. SENSOR CONFIGURATION

X4  is  an  auxiliary  sensor  input  mainly  intended  for  supply  air  measurement  as 

feedback on the performance of the air conditioning supply air output, but currently 

performs no other function (In future updates this sensor could be used for room to 

supply air cascade control or supply air min / max limitation). This sensor reading is 

also available in the modbus output for zone display information on the Hevac HMI 

panel or for use by 3rd party BMS suppliers. The input can be set as either a Passive 

(Hevac  type  -D  sensors)  or  as  Active  type  (0-10vdc)  in  software  but  must  also  be 

selected as a passive or active  type  in  hardware  with  a  small  jumper  (CN2-2)  on 

the  bottom  circuit  board  to  match  the  software setting.  Offset  (cal)  adjustment  is 

settable  for  both  passive  &  active  types  &  for  active  sensors  the  maximum 

range is also adjustment ie: 10v = 20 ~ 100c

LAST SET STATE DISPLAYED

Note if active sensor type is selected, it is also necessary to reposition a physical input 

select jumper on the controller's bottom pcb. Remove screws holding the lid to base and 

hinge lid to the right, locate the row of red jumpers located under the X1-X7 terminal strip. 

Reposition the CN2-2 jumper (4th of 7 jumpers from left) to short the top two pins 

(V position) for active sensor selection. The bottom two pins (T position) are used for 

passive resistance type sensors selection (factory default)... SEE IMAGE ABOVE. 

For active sensors also note 0v equates to 0c unless offset by the software offset setting...

(=)

HEVAC CONTROL AGENCIES PTY LTD.  7/54 HOWLEYS RD. 

NOTTINGHILL,  VIC.  95627888 

www.hevac.com.au

  

 

21/10/19

TO USE ACTIVE SENSORS INSTEAD OF 

PASSIVE , MOVE JUMPERS AS INDICATED. 

MODBUS ( TERMINALS X5 & X6) ARE 

FACTORY SET TO COMMS MODE "C" 

USING THE CN3-1 & 2 JUMPERS. ALSO

IF X7 ISNT BEING USED AS A CO2 SENSOR 

INPUT, MOVE CN3-3 TO THE C POSITION & 

USE X7 FOR CABLE SHIELD CONNECTION.

19/2

8

CONTROLLER BOTTOM PCB SHOWING SENSOR PASSIVE / ACTIVE 

RED 

SELECTION PINS

CN1-1 :X1 MAIN SENSOR

 

CN1-2 :X2 

REMOTE 

SETPOINT

CN2-1 : X3 O/A SENSOR

 

CN2-2 :X4 AUX. SENSOR

CN3-1 : X5 MODBUS A

CN3-2 : X6 MODBUS B

CN3-3 : X7 CO2 SENSOR  

            OR 

MODBUS SHIELD

Summary of Contents for ENDEAVOUR V2




























Reviews: