Hensel-Visit Certo 200 User Manual Download Page 3

Page: 3 / 56

Mounting the device on/removing it from a stand ............................... 32

Rotating and tilting the device .............................................................. 33

Mounting the umbrella on/removing it from the device ...................... 35

Operating the device ............................................................................ 36

Activating and deactivating the device ................................................. 36

Triggering a test flash ............................................................................ 36

Activating and deactivating the model light .......................................... 37

Checking the function of the model light .............................................. 37

Setting the flash energy ......................................................................... 38

Activating and deactivating the “Audio” function ................................. 39

Synchronizing the device with the camera............................................ 40

Error messages ..................................................................................... 43

Transporting and storing the device ...................................................... 44

Servicing the device .............................................................................. 45

Caring for and cleaning the device ........................................................ 45

Exchanging the defective flash tube with protection glass ................... 46

Replacing a defective model light ......................................................... 47

Replacing a defective fuse of the model light ....................................... 48

Replacing a defective fuse of the mains connection ............................. 49

Disposing of the device and packaging .................................................. 50

In Germany ............................................................................................ 50

Outside of Germany .............................................................................. 50

EU Declaration of Conformity ............................................................... 51

Accessories ........................................................................................... 52

Flash tubes ............................................................................................. 52

Illuminant for model light ...................................................................... 52

Fuses ...................................................................................................... 52

Light shaping tools ................................................................................. 52

Additional accessories ........................................................................... 52

Summary of Contents for Certo 200

























































Search results

Summary of Contents for Certo 200

Reviews:

Related manuals for Certo 200

Brands by name

Popular brands

Hensel-Visit Certo 200, User Manual

Search results

Summary of Contents for Certo 200

Reviews:

Related manuals for Certo 200

Brands by name

Popular brands